Repository logo
 

The effects of bend radius on flow around a configuration of bendway weirs: insight from a numerical model

Simple item page
dc.contributor.authorHogan, Taylor, author
dc.contributor.authorThornton, Christopher, advisor
dc.contributor.authorEttema, Robert, advisor
dc.contributor.authorWilliams, John, committee member
dc.date.accessioned2019-09-10T14:36:05Z
dc.date.available2019-09-10T14:36:05Z
dc.date.issued2019
dc.description.abstractBendway weirs have been used and refined for decades by hydraulic engineers to control thalweg location within alluvial rivers and to decrease flow velocity along the outer bank of channel bends. Although these structures have been used in a variety of applications, there are still a wide range of acceptable design parameters that vary in accordance with the specific design methodology being used. Since the early 2000s, Colorado State University's Hydraulics Lab has assisted The U.S Bureau of Reclamation (USBR) in refining the design of bendway weirs and similar in-stream rock structures. During this period of time, Colorado State University and The USBR have utilized hydraulic and numerical models to develop systematic design guidelines for bendway weirs and other in-stream rock structures. Hydraulic modeling has also provided a large database of velocity and water surface measurements that have been used to calibrate and validate subsequent numerical models. The partnership between Colorado State University and the USBR has led to design recommendations and equations in which the effect of many variables and their sensitivity in overall bendway weir design has been identified. This study investigates the parameter radius of curvature over channel top width, Rc/Tw, and its effect on the flow field around bendway weirs, as its significance in bendway weir design is not well known. To investigate the effects of Rc/Tw on the bendway weir flow field, the 2D numerical model SRH-2D was used in conjunction with AutoCAD Civil3D software. The SRH-2D model was created using the bathymetry of the hydraulic model and then also calibrated and validated using data collected in the hydraulic model. AutoCAD Civil3D was used to create four different bend radii while holding Tw constant, representing Rc/Tw values between 3.0 and 8.0 which are typical of the Middle Rio Grande that the hydraulic model represented. Two additional trapezoidal channel models were also created to isolate the possible effects from specific channel geometry on the bendway weir flow field comparisons. 2D numerical modeling results revealed that the bend radius of curvature had negligible effect on the bendway weir flow field. Velocity patterns in the trapezoidal and native bathymetry channels changed negligibly in location and magnitude across varying bend radii. Cross-sectional velocity distributions were also evaluated and showed that the inner and middle third lateral sections of the channel showed the same (within fractions of a percent) velocity increase after the installation of bendway weirs. The outer fifth of the channel resulted in 6% velocity decrease only varying approximately 0.1% between bend radii. Overall numerical modeling results showed that the bendway weir flow field was negligibly affected by the bend radius of curvature, Rc.
dc.format.mediumborn digital
dc.format.mediummasters theses
dc.identifierHogan_colostate_0053N_15591.pdf
dc.identifier.urihttps://hdl.handle.net/10217/197362
dc.languageEnglish
dc.language.isoeng
dc.publisherColorado State University. Libraries
dc.relation.ispartof2000-2019
dc.rightsCopyright and other restrictions may apply. User is responsible for compliance with all applicable laws. For information about copyright law, please see https://libguides.colostate.edu/copyright.
dc.subjectchange of bend radius
dc.subjectbendway weirs
dc.subjectSRH-2D
dc.titleThe effects of bend radius on flow around a configuration of bendway weirs: insight from a numerical model
dc.typeText
dcterms.rights.dplaThis Item is protected by copyright and/or related rights (https://rightsstatements.org/vocab/InC/1.0/). You are free to use this Item in any way that is permitted by the copyright and related rights legislation that applies to your use. For other uses you need to obtain permission from the rights-holder(s).
thesis.degree.disciplineCivil and Environmental Engineering
thesis.degree.grantorColorado State University
thesis.degree.levelMasters
thesis.degree.nameMaster of Science (M.S.)

Files

Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
Hogan_colostate_0053N_15591.pdf
Size:
8.03 MB
Format:
Adobe Portable Document Format
Download

Collections

2000-2019
Theses and Dissertations