Browsing by Author "Li, Vivian, committee member"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Embargo Failure analysis and durability enhancement of polymeric heart valve leaflets(Colorado State University. Libraries, 2024) Khair, Nipa, author; James, Susan P., advisor; Bailey, Travis S., advisor; Li, Vivian, committee member; McGilvray, Kirk, committee memberRheumatic and calcified aortic heart valve disease is prevalent globally among all aged people, and the number is rapidly increasing. Clinically accepted, minimally invasive xenograft-based transcatheter aortic heart valve replacement (TAVR) shows limited durability (<10 years). Hyaluronic acid (HA) enhanced polyethylene polymeric TAVR shows excellent in vitro and in vivo anti-calcific, anti-thrombotic, and hydrodynamic performance, making it a suitable candidate for heart valve leaflets. The main problem, however, is during durability testing, cyclic impact loading causes premature failure in a consistent fashion related to TAVR assembly. This dissertation investigates leaflet premature failure mechanisms and provides two plausible solutions to upgrade heart valve durability without sacrificing performance. With regard to the failure mechanism, representative areas of retrieved failed leaflets are examined under electron microscopy and small angle x-ray scattering. The investigation finds abrasive wear, wear polishing, fine scratching, and imprints of the metal stent of the leaflet surface, indicating surface wearing from soft plastic rubbing against hard metal. A strong permanganate oxidizer etches away low-energy amorphous domain to unveil stable spherulitic structures of approximately 3 µm, bridging and tie molecular domains of pristine LLDPE. The oxidizer partially etches away polymeric buildups of failed leaflets only to reveal thinned-out and fractured spherulites beneath them, identifying the buildups as stress precursors. SAXS study reports local lamellar disruption further confirming the SEM results. Most. Notably, this is the first study that, to our knowledge, to directly image stable craze cross-tie microstructure that formed due to chain disentanglement from high amplitude cyclic stress. The SEM images validate previous theoretical and computational molecular dynamics models of cross-tie structure architecture. Therefore, leaflet premature failures are the compound effect of cyclic fatigue-initiated crazing and surface wear. Heart valve leaflet durability can be upgraded by controlling crazing and surface wearing. Both the crazing and surface wearing can be controlled by crosslinking of randomly folded amorphous chains. Because they are direct impacts of chain disentanglement under high amplitude cyclic stress. Crosslinked covalent bonds of polymer limit chain movements. LLDPE thin sheets are crosslinked at 50, 70, 100, and 150 kGy doses using 200 KeV (low energy) and 4 MeV (low energy) electron beams at room temperature in the air. Their effects are characterized by measuring gel content percentage, tensile testing, Differential Scanning Calorimetry (DSC), nanoindentation, and nano scratch test. Crosslinked LLDPE heart valve leaflet tested in in vitro flow loop and wear tester to determine valve performance and durability, respectively. Low energy electron beam (LEEB) forms 28% xylene insoluble gel whereas high energy electron beam (HEEB) forms 58 % gel at 100 kGy doses. LEEB does not affect mechanical properties, but HEEB significantly increases stiffness and yield strength. A slight reduction of melting temperature is found for LLDPE crosslinked by both of the energy sources. Nanomechanical tests show crosslinking improves hardness and coefficient of friction, an indication of improving surface wear resistance, which can explain durability improvement. Heart valve durability can also be improved by strengthening the leaflet with fiber reinforcement. A thin plastic sheet is assembled into a cylindrical form by welding two ends, which never fails. The weld at the commissure post is found to be mechanically stronger than the rest of the leaflet, which protected this region. Braided fibers are embedded on the leaflet regions of the commissure post perpendicular to the valve circumference, mimicking the weld but at a much higher strength. Leaflet durability skyrockets from a few million ISO 5840-2005 cycles to 73 million. The entire cardiac cycle of the heart valve with embedded fibers of varying angles, lengths, and numbers is simulated in Finite Element Analysis (FEA) to study their effects on leaflet maximum principal stress and leaflet opening dynamics. Horizontal fibers wrap the leaflet 360° to relax the leaflet completely during peak diastolic. However, the leaflet has a higher coaptation gap and delayed opening. The heart valve with embedded horizontal fibers is physically manufactured and tested in an in vitro flow loop and wear tester, which showed improved durability, but compromised hemodynamics. Finally, strategically crosslinked leaflet was simulated in FEA where leaflet regions of the commissure post and stent line are assigned with stiff crosslinked LLDPE material property, but the rest of the cusps undergo maximum bending are assigned with uncrosslinked LLDPE material property. Results show that strategically crosslinked leaflets open more easily than fully crosslinked leaflets. The final chapter discusses 3D shaped LLDPE leaflet bio enhancement process. Leaflets are 3D shaped in a vacuum thermoformer followed by the HA enhancement. Whole blood clotting resistance, platelet adhesion, activation, and cytotoxicity studies are conducted to determine at 10-4 µmol/mm2 ranged HA population density is required to achieve the best biocompatibility. Generally, water contact angle, Toluidine Blue O (TBO) elution assays, ATR-FTIR are used to determine overall HA presence on the leaflet. This study reports TBO staining and elution is the most effective and accurate measurement tool for determining HA population density. Fiber-reinforced LLDPE, and crosslinked LLDPE are HA-treated, and TBO staining predicts heavily populated HA surface density.Item Open Access Interaction of erythrocytes (RBC's) with nanostructured surfaces(Colorado State University. Libraries, 2022) Virk, Harvinder Singh, author; Popat, Ketul C., advisor; Ghosh, Soham, committee member; Li, Vivian, committee memberTitanium and its alloys are used to make different blood-contacting medical devices such as stents, artificial heart valves, and catheters for cardiovascular diseases due to their superior biocompatibility. Thrombus formation begins on the surface of these devices as soon as they encounter blood. This leads to the formation of blood clots, which obstructs the flow of blood that leads to severe complications. Recent advancements in nanoscale fabrication and superhydrophobic surface modification techniques have demonstrated that these surfaces have antiadhesive properties and the ability to reduce thrombosis. In this study, the interaction of erythrocytes and whole blood clotting kinetics on superhydrophobic titanium nanostructured surfaces was investigated. These surfaces were characterized for their wettability (contact angle), surface morphology and topography (scanning electron microscopy (SEM)), and crystallinity (glancing angled X-Ray diffraction (GAXRD)). Erythrocyte morphology on different surfaces was characterized using SEM and overall cell viability was demonstrated through fluorescence microscopy. The hemocompatibility of these surfaces was characterized using commercially available assays: thrombin generation assay --> thrombin generation, hemolytic assay --> hemolysis, and complement convertase assay --> complement activity. The results indicate that superhydrophobic titanium nanostructured surfaces had lower erythrocyte adhesion, less morphological changes in adhered cells, lower thrombin generation, lower complement activation, and were less cytotoxic compared to control surfaces. Thus, superhydrophobic titanium nanostructured surfaces may be a promising approach to prevent thrombosis for several blood-contacting medical devices.Item Open Access Superhydrophobic titania nanoflowers for reducing adhesion of platelets and bacteria(Colorado State University. Libraries, 2020) Montgomerie, Zachary Z., author; Popat, Ketul C., advisor; Li, Vivian, committee member; Sampath, Walajabad S., committee memberThrombosis formation and bacterial infection are key challenges for blood-contacting medical devices. When blood components encounter a device's surface, proteins are adsorbed, followed by the adhesion and activation of platelets as well as an immune response. This culminates in clot formation via the trapping of red blood cells in a fibrin matrix, which can block the device's function and cause severe complications for the patient. Bacteria may also adhere to a device's surface. This can lead to the formation of a biofilm, a protective layer for bacteria that significantly increases resistance to antibiotics. Despite years of research, no long-term solutions have been discovered to combat these issues. To impede thrombosis, patients often take antiplatelet drugs for the life of their device, which can cause excess bleeding and other complications. Patients can take antibiotics to fight bacterial infection, but these are often ineffective if biofilms are formed. Superhydrophobic surfaces have recently been studied for their antiadhesive properties and show promise in reducing both thrombosis and bacterial infection. In this work, superhydrophobic titania nanoflower surfaces were successfully fabricated on a titanium alloy Ti-6Al-4V substrate and examined for both hemocompatibility and bacterial adhesion. The results indicated a reduction of protein adsorption, platelet and leukocyte adhesion and activation, whole blood clotting, bacterial adhesion, and biofilm formation, as well as surface stability compared to control surfaces.